Techspray WonderMASK WSOL
| Section 1. Identification |
| GHS product identifier | : Techspray WonderMASK WSOL |
| Product code | : 2204-G, 5G |
| Other means of identification | : Not available. |
| Product type | : Liquid. |
Relevant identified uses of the substance or mixture and uses advised against: Not applicable.
|
Supplier's details
|
: Techspray |
| Emergency telephone number (with hours of operation) | : Chemtrec - 1-800-424-9300 CANUTEC (Canadian Transportation): (613) 996-6666 Emergency phone: (800) 858-4043 24/7 |
| Section 2. Hazards identification |
| OSHA/HCS status | : This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200). |
| Classification of the substance or mixture | : FLAMMABLE LIQUIDS - Category 2 SKIN IRRITATION - Category 2 EYE IRRITATION - Category 2A |
Percentage of the mixture consisting of ingredient(s) of unknown toxicity: 40.5% |
|
| GHS label elements | |
| Hazard pictograms |
: |
| Signal word | : Danger |
| Hazard statements | : Highly flammable liquid and vapor.Causes serious eye irritation.Causes skin irritation. |
| Precautionary statements | |
| Prevention | : Wear protective gloves. Wear eye or face protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Use explosion- proof electrical, ventilating, lighting and all material-handling equipment. Use only non-sparking tools. Take precautionary measures against static discharge. Keep container tightly closed. Wash hands thoroughly after handling. |
| Response | : IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower. IF ON SKIN: Wash with plenty of soap and water. Take off contaminated clothing and wash it before reuse. If skin irritation occurs: Get medical attention. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. |
| Storage | : Store in a well-ventilated place. Keep cool. |
| Disposal | : Dispose of contents and container in accordance with all local, regional, national and international regulations. |
| Hazards not otherwise classified | : None known. |
| Section 3. Composition/information on ingredients |
| Substance/mixture | : Mixture |
| Other means of identification | : Not available. |
| Ingredient name | % | CAS number |
|
methanol 2,4,7,9-tetramethyldec-5-yne-4,7-diol glycerol |
≥25 - ≤50 ≤5 ≤3 |
67-56-1 126-86-3 56-81-5 |
Any concentration shown as a range is to protect confidentiality or is due to batch variation.
There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health or the environment and hence require reporting in this section.
Occupational exposure limits, if available, are listed in Section 8.
| Section 4. First aid measures |
Description of necessary first aid measures
| Eye contact | : Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. Get medical attention. |
|
Inhalation
|
: Remove victim to fresh air and keep at rest in a position comfortable for breathing. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Get medical attention if adverse health effects persist or are severe. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar,tie, belt or waistband. In case of inhalation of decomposition products in a fire,symptoms may be delayed. The exposed person may need to be kept under medical surveillance for 48 hours. |
| Skin contact | : Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Continue to rinse for at least 10 minutes. Get medical attention. Wash clothing before reuse. Clean shoes thoroughly before reuse. |
| Ingestion | : Wash out mouth with water. Remove dentures if any. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Get medical attention if adverse health effects persist or are severe. Never give anything by mouth to an unconscious person.If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. |
| Most important symptoms effects, acute and delayed | |
| Potential acute health effects | |
| Eye contact | : Causes serious eye irritation. |
| Inhalation | : Exposure to decomposition products may cause a health hazard. Serious effects may be delayed following exposure. |
| Skin contact | : Causes skin irritation. |
| Ingestion | : Do not ingest. If swallowed then seek immediate medical assistance. |
| Over-exposure signs/symptoms | |
| Eye contact | : Adverse symptoms may include the following:pain or irritation watering redness |
| Inhalation | : Adverse symptoms may include the following:respiratory tract irritation coughing |
| Skin contact | : Adverse symptoms may include the following:irritation redness dryness cracking |
| Ingestion | : Adverse symptoms may include the following:nausea or vomiting diarrhea Ingestion Seek medical attention. |
Indication of immediate medical attention and special treatment needed, if necessary
| Notes to physician | : In case of inhalation of decomposition products in a fire, symptoms may be delayed.The exposed person may need to be kept under medical surveillance for 48 hours. |
| Specific treatments | : No specific treatment. |
| Protection of first-aiders | : No action shall be taken involving any personal risk or without suitable training. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. |
See toxicological information (Section 11)
| Section 5. Fire-fighting measures |
Extinguishing media
| Suitable extinguishing media | : Use dry chemical, CO2, water spray (fog) or foam. |
| Unsuitable extinguishing media | : Do not use water jet. |
| Specific hazards arising from the chemical | : Highly flammable liquid and vapor. In a fire or if heated, a pressure increase will occur and the container may burst, with the risk of a subsequent explosion. Runoff to sewer may create fire or explosion hazard. |
| Hazardous thermal decomposition products | : Decomposition products may include the following materials:carbon dioxide carbon monoxide nitrogen oxides metal oxide/oxides |
| Special protective actions for fire-fighters | : Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. Move containers from fire area if this can be done without risk. Use water spray to keep fire-exposed containers cool. |
| Special protective equipment for fire-fighters | : Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode. |
| Section 6. Accidental release measures |
Personal precautions, protective equipment and emergency procedures
|
For non-emergency personnel
|
: No action shall be taken involving any personal risk or without suitable training.Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. In the case of aerosols being ruptured, care should be taken due to the rapid escape of the pressurized contents and propellant. If a large number of containers are ruptured, treat as a bulk material spillage according to the instructions in the clean-up section. Do not touch or walk through spilled material. Avoid breathing vapor or mist. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. |
| For emergency responders | : If specialized clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also the information in "For non- emergency personnel". |
| Environmental precautions | : Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air). |
| Methods and materials for containment and cleaning up | |
| Small spill | : Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Dispose of via a licensed waste disposal contractor. |
|
Large spill
|
: Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations (see Section 13). Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Note: see Section 1 for emergency contact information and Section 13 for waste disposal. |
| Section 7. Handling and storage |
Precautions for safe handling
| Protective measures | : Put on appropriate personal protective equipment (see Section 8). Avoid exposure obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Do not get in eyes or on skin or clothing. Do not ingest.Avoid breathing vapor or mist. If during normal use the material presents a respiratory hazard, use only with adequate ventilation or wear appropriate respirator. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Empty containers retain product residue and can be hazardous. Do not reuse container. |
| Advice on general occupational hygiene | : Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures. |
| Conditions for safe storage, including any incompatibilities | : Store in accordance with local regulations. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Store locked up. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate containment to avoid environmental contamination. |
| Section 8. Exposure controls/personal protection |
Control parameters
Occupational exposure limits
| Ingredient name | Exposure limits |
|
methanol
2,4,7,9-tetramethyldec-5-yne-4,7-diol glycerol |
ACGIH TLV (United States, 3/2015). Absorbed through skin. None. OSHA PEL (United States, 2/2013). |
| Appropriate engineering controls | : Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended or statutory limits. The engineering controls also need to keep gas,vapor or dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment. |
| Environmental exposure controls | : Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels. |
| Individual protection measures | |
| Hygiene measures | : Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period.Appropriate techniques should be used to remove potentially contaminated clothing.Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location. |
| Eye/face protection | : Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists,gases or dusts. If contact is possible, the following protection should be worn, unless the assessment indicates a higher degree of protection: chemical splash goggles. |
| Skin protection | |
| Hand protection | : Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties. It should be noted that the time to breakthrough for any glove material may be different for different glove manufacturers. In the case of mixtures, consisting of several substances, the protection time of the gloves cannot be accurately estimated. |
| Body protection | : Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. When there is a risk of ignition from static electricity, wear anti-static protective clothing. For the greatest protection from static discharges, clothing should include anti-static overalls, boots and gloves. |
| Other skin protection | : Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. |
| Respiratory protection | : Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification. Respirators must be used according to a respiratory protection program to ensure proper fitting, training, and other important aspects of use. |
| Section 9. Physical and chemical properties |
| Appearance | |
| Physical state | : Liquid. [Gel] |
| Color | : Pink Red. |
| Odor | : Alcohol-like. |
| Odor threshold | : Not available. |
| pH | : Not available. |
| Melting point | : Not available. |
| Boiling point | : Not available. |
| Flash point | : Closed cup: 13°C (55.4°F) [Tagliabue.] |
| Evaporation rate | : Not available. |
| Flammability (solid, gas) | : Not available. |
| Lower and upper explosive (flammable) limits | : Lower: 7.3% Upper: 36% |
| Vapor pressure | : Not available. |
| Vapor density | : Not available. |
| Relative density | : Not available. |
| Solubility | : Not available. |
| Solubility in water | : Not available. |
| Partition coefficient: n- octanol/water | : Not available. |
| Auto-ignition temperature | : Not available. |
| Decomposition temperature | : Not available. |
| Viscosity | : Not available. |
| Aerosol product | |
| Type of aerosol | : Not available. |
| Heat of combustion | : Not available. |
| Ignition distance | : Not available. |
| Enclosed space ignition - Time equivalent | : Not available. |
| Enclosed space ignition - Deflagration density | : Not available. |
| Section 10. Stability and reactivity |
| Reactivity | : No specific test data related to reactivity available for this product or its ingredients. |
| Chemical stability | : The product is stable. |
| Possibility of hazardous reactions | : Under normal conditions of storage and use, hazardous reactions will not occur. |
| Conditions to avoid | : Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld,braze, solder, drill, grind or expose containers to heat or sources of ignition. |
| Incompatible materials | : Reactive or incompatible with the following materials:oxidizing materials |
| Hazardous decomposition products | : Under normal conditions of storage and use, hazardous decomposition products should not be produced. |
| Section 11. Toxicological information |
Information on toxicological effects
Acute toxicity
| Product/ingredient name | Result | Species | Dose | Exposure |
|
methanol
glycerol |
LC50 Inhalation Gas. LC50 Inhalation Gas. LD50 Dermal LD50 Oral LD50 Oral |
Rat Rat Rabbit Rat Rat |
145000 ppm 64000 ppm 15800 mg/kg 5600 mg/kg 12600mg/kh |
1 hours 4 hours - - - |
Irritation/Corrosion
| Product/ingredient name | Result | Species | Score | Exposure | Observation |
|
methanol
2,4,7,9-tetramethyldec-5-yne- glycerol |
Eyes - Moderate irritant Eyes - Moderate irritant Skin - Moderate irritant Eyes - Severe irritant Skin - Mild irritant Eyes - Mild irritant Skin - Mild irritant |
Rabbit Rabbit Rabbit Rabbit Rabbit Rabbit Rabbit |
- - - - - - - |
24 hours 100 milligrams 40 milligrams 24 hours 20 milligrams 0.1 Mililiters 0.5 Grams 24 hours 500 milligrams 24 hours 500 milligrams |
- - - - - - |
Sensitization
Not available.
Mutagenicity
Not available.
Carcinogenicity
Not available.
Classification
Not available.
Reproductive toxicity
Not available.
Teratogenicity
Not available.
Specific target organ toxicity (single exposure)
Not available.
Specific target organ toxicity (repeated exposure)
Not available.
Aspiration hazard
Not available.
|
Information on the likely routes of exposure |
: Not available. |
| Potential acute health effects | |
| Eye contact | : Causes serious eye irritation. |
| Inhalation | : Exposure to decomposition products may cause a health hazard. Serious effects may be delayed following exposure. |
| Skin contact | : Causes skin irritation. |
| Ingestion | : Do not ingest. If swallowed then seek immediate medical assistance. |
Symptoms related to the physical, chemical and toxicological characteristics
| Eye contact | : Adverse symptoms may include the following:pain or irritation watering redness |
| Inhalation | : Adverse symptoms may include the following:headache central nervous system depression nausea or vomiting |
| Skin contact | : Adverse symptoms may include the following:irritation redness dryness cracking |
| Ingestion | : Adverse symptoms may include the following:nausea or vomiting diarrhea Ingestion Seek medical attention. |
Delayed and immediate effects and also chronic effects from short and long term exposure
Short term exposure
| Potential immediate effects | : Not available. |
| Potential delayed effects | : Not available. |
| Long term exposure | |
| Potential immediate effects | : Not available. |
| Potential delayed effects | : Not available. |
| Potential chronic health effects | : Not available. |
| General | : No known significant effects or critical hazards. |
| Carcinogenicity | : No known significant effects or critical hazards. |
| Mutagenicity | : No known significant effects or critical hazards. |
| Teratogenicity | : No known significant effects or critical hazards. |
| Developmental effects | : No known significant effects or critical hazards. |
| Fertility effects | : No known significant effects or critical hazards. |
Numerical measures of toxicity
Acute toxicity estimates
| Route | ATE value |
| Oral | 25069.3 mg/kg |
| Section 12. Ecological information |
Toxicity
| Product/ingredient name | Result | Species | Exposure |
|
methanol
|
Acute EC50 16.912 mg/l Marine water Acute LC50 2500000 μg/l Marine water Acute LC50 3289 to 4395 mg/l Fresh water Acute LC50 290 mg/l Fresh water Chronic NOEC 9.96 mg/l Marine water |
Algae - Ulva pertusa Crustaceans - Crangon crangon - Adult Daphnia - Daphnia magna - Neonate Fish - Danio rerio - Egg Algae - Ulva pertusa |
96 hours 48 hours 48 hours 96 hours 96 hours |
Persistence and degradability: Not available.
Bioaccumulative potential
| Product/ingredient name | LogPow | BCF | Potential |
|
methanol glycerol |
-0.77 -1.76 |
<10 - |
low low |
Mobility in soil
| Soil/water partition coefficient (KOC) | : Not available. |
| Other adverse effects | : No known significant effects or critical hazards. |
| Section 13. Disposal considerations |
| Disposal methods | :The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless fully compliant with the requirements of all authorities with jurisdiction.Waste packaging should be recycled. Incineration or landfill should only be considered when recycling is not feasible. This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues.Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. |
United States - RCRA Toxic hazardous waste "U" List
| Ingredient | CAS # | Status | Reference number |
| Methanol (I); Methyl alcohol (I) | 67-56-1 | Listed | U154 |
| Section 14. Transport information |
| DOT Classification | TDG Classification | Mexico Classification | ADR/RID | IMDG | IATA | |
| UN number | UN1139 | UN1139 | UN1139 | UN1139 | UN1139 | ID8000 |
| UN proper shipping name | Coating Solution | Coating Solution | Coating Solution | Coating Solution | Coating Solution | Coating Solution |
| Transport hazard class(es) |
3 |
3 |
3 |
3 |
3 |
3 |
| Packing group | II |
II | II | II | II | II |
| Environmental hazards | No. | No. | No. | No. | No. | No. |
Additional information |
Reportable quantity 11111.1 lbs /5044.4 kg [1293.8 gal /4897.5 L] Package sizes shipped in quantities less than the product reportable quantity are not subject to the RQ (reportable quantity) transportation requirements. |
Product classified asper the following sections of the Transportation of Dangerous Goods Regulations: 2.18-2.19 (Class 3). |
- |
Special provisions 640 (C) |
- | - |
| Special precautions for user | : Transport within user’s premises: always transport in closed containers that are upright and secure. Ensure that persons transporting the product know what to do in the event of an accident or spillage. |
| Transport in bulk according to Annex II of MARPOL and the IBC Code | : Not available. |
| Section 15. Regulatory information |
| U.S. Federal regulations |
: TSCA 8(a) PAIR: 5,12-dihydroquino[2,3-b]acridine-7,14-dione Clean Water Act (CWA) 307: copper dinitrate |
| Clean Air Act Section 112 (b) Hazardous Air Pollutants (HAPs) | : listed |
| Clean Air Act Section 602 Class I Substances | : Not listed |
| Clean Air Act Section 602 Class II Substances | : Not listed |
| DEA List I Chemicals (Precursor Chemicals) | : Not listed |
| DEA List II Chemicals (Essential Chemicals) | : Not listed |
| SARA 302/304 | |
| Composition/information on ingredients | : No products were found. |
| SARA 304 RQ | : Not applicable. |
| SARA 311/312 | |
| Classification |
: Fire hazard Immediate (acute) health hazard Composition on ingredients |
| Name | % | Fire hazard | Sudden release of pressure | Reactive |
Immediate (acute) health hazard |
Delayed (chronic) health hazard |
|
methanol 2,4,7,9 tetramethyldec-5-yne-4,7-diol glycerol |
≥25 - ≤50 ≤5 ≤3 |
Yes. No. No. |
No. No. No. |
No. No. No. |
Yes. Yes. Yes. |
No. No. No. |
SARA 313
| Product name | CAS number | % | |
| Form R - Reporting requirements | methanol | 67-56-1 | ≥25 - ≤50 |
| Supplier notification | methanol | 67-56-1 | ≥25 - ≤50 |
SARA 313 notifications must not be detached from the SDS and any copying and redistribution of the SDS shall include copying and redistribution of the notice attached to copies of the SDS subsequently redistributed.
State regulations
| Massachusetts | : The following components are listed: METHANOL; METHYL ALCOHOL; GLYCERINE MIST |
| New York | : The following components are listed: Methanol |
| New Jersey | : The following components are listed: METHYL ALCOHOL; METHANOL; GLYCERIN; 1,2,3-PROPANETRIOL |
| Pennsylvania | : The following components are listed: METHANOL; 1,2,3-PROPANETRIOL |
| International regulations |
California Prop. 65
WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.
| Ingredient name | Cancer | Reproductive | No significant risk level |
Maximum acceptable dosage level |
| methanol | No. | Yes. | No. | 23000 μg/day (ingestion) 47000 μg/day (inhalation) |
International regulations
Chemical Weapon Convention List Schedules I, II & III Chemicals: Not listed.
Montreal Protocol (Annexes A, B, C, E): Not listed.
Stockholm Convention on Persistent Organic Pollutants: Not listed.
Rotterdam Convention on Prior Informed Consent (PIC): Not listed.
UNECE Aarhus Protocol on POPs and Heavy Metals: Not listed.
International lists
National inventory
| Australia | : All components are listed or exempted. |
| Canada | : All components are listed or exempted. |
| China | : All components are listed or exempted. |
| Europe | : Not determined. |
| Japan |
: Japan inventory (ENCS): All components are listed or exempted. Japan inventory (ISHL): Not determined. |
| Malaysia | : Not determined. |
| New Zealand | : All components are listed or exempted. |
| Philippines | : All components are listed or exempted. |
| Republic of Korea | : All components are listed or exempted. |
| Taiwan | : All components are listed or exempted. |
| Turkey | : Not determined. |
| Section 16. Other information |
Hazardous Material Information System (U.S.A.)
Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant hazards or risks Although HMIS® ratings are not required on SDSs under 29 CFR 1910. 1200, the preparer may choose to provide them. HMIS® ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered mark of the National Paint & Coatings Association (NPCA). HMIS® materials may be purchased exclusively from J. J. Keller (800) 327-6868.
The customer is responsible for determining the PPE code for this material.
National Fire Protection Association (U.S.A.)
Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency Response Copyright ©1997, National Fire Protection Association, Quincy, MA 02269. This reprinted material is not the complete and official position of the National Fire Protection Association, on the referenced subject which is represented only by the standard in its entirety.
Copyright ©2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to be interpreted and applied only by properly trained individuals to identify fire, health and reactivity hazards of chemicals. The user is referred to certain limited number of chemicals with recommended classifications in NFPA 49 and NFPA 325, which would be used as a guideline only. Whether the chemicals are classified by NFPA or not, anyone using the 704 systems to classify chemicals does so at their own risk.
Procedure used to derive the classification
| Classification | Justification |
|
FLAMMABLE LIQUIDS - Category 2 SKIN IRRITATION - Category 2 EYE IRRITATION - Category 2A |
On basis of test data Calculation method Calculation method |
History
| Date of printing | : 6/27/2019 |
|
Date of issue/Date of revision |
: 6/27/2019 |
| Date of previous issue | : No previous validation |
| Version | : 1 |
| Key to abbreviations | : ATE = Acute Toxicity Estimate BCF = Bioconcentration Factor GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association IBC = Intermediate Bulk Container IMDG = International Maritime Dangerous Goods LogPow = logarithm of the octanol/water partition coefficient MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution) UN = United Nations |
| References | : Not available. |
Indicates information that has changed from previously issued version.
Notice to reader
To the best of our knowledge, the information contained herein is accurate. However, neither the above-named supplier, nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the information contained herein.
Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.