Desco Reztore Antistatic Coating
May be used to comply with OSHA Hazcom 29 CFR 1910.1200. Standards must be consulted for specific requirements.
1. IDENTIFICATION
| Product Name: | Reztore® Antistatic Coating |
| Identified use: | Antistatic coating |
| Company Identification |
DESCO One Colgate Way Canton, MA 02021 UNITED STATES +1 781-821-8370 |
| Email Address: | [email protected] |
| Emergency telephone number United States: | +1 781-821-8370 |
Office hours: 8:00 AM - 5:00 PM
2. HAZARDS IDENTIFICATION
Hazard classification
This material is non-hazardous under the criteria of the Federal OSHA Hazcom 29 CFR 1910.1200.
Label elements
This material is non-hazardous under the criteria of the Federal OSHA Hazcom 29 CFR 1910.1200.
3. COMPOSITION/INFORMATION ON INGREDIENTS
This product is a mixture.
| Components | CAS No. | Concentration |
| Ethylene glycol monobutyl ether | 111-76-2 | 5 - 25% |
| Diethylene glycol | 111-46-6 | < 1% |
4. FIRST AID MEASURES
Description of first aid measures
| General advice: |
First Aid responders should pay attention to self-protection and use there commended protective clothing (chemical resistant gloves, splashprotection). If potential for exposure exists refer to Section 8 for specific personal protective equipment. |
| Eye Contact |
Immediately flush eyes with water; remove contact lenses, if present, after the first 5 minutes, then continue flushing eyes for at least 15 minutes. Obtain medical attention without delay, preferably from an ophthalmologist. Suitable emergency eye wash facility should be immediately available. |
| Skin Contact |
In case of contact, immediately flush with plenty of water. If irritation occurs and persists, get medical attention. |
| Ingestion | Rinse mouth. If you feel unwell, get medical attention. |
| Inhalation | Remove person to fresh air. If you feel unwell, get medical attention. |
Most important symptoms and effects, both acute and delayed
Aside from the information found under Description of first aid measures (above) and Indication of immediate medical attention and special treatment needed (below), any additional important symptoms and effects are described in Section 11: Toxicology Informatio
Indication of any immediate medical attention and special treatment needed
N/A
5. FIRE FIGHTING MEASURES
Extinguishing media
| Suitable Extinguishing Media |
Water fog or fine spray. Dry chemical fire extinguishers. Carbon dioxide fire extinguishers. Foam. Alcohol resistant foams (ATC type) are preferred. General purpose synthetic foams (including AFFF) or protein foams may function, but will be less effective. |
| Unsuitable Extinguishing Methods | Do not use direct water stream. May spread fire. |
Special hazards arising from the substance or mixture
Hazardous combustion products: products: During a fire, smoke may contain the original material in addition to combustion products of varying composition which may be toxic and/or irritating. Combustion products may include and are not limited to: Carbon monoxide. Carbon dioxide
Unusual Fire and Explosion Hazards: Container may rupture from gas generation in a fire situation. Violent steam generation or eruption may occur upon application of direct water stream to hot liquids.
Advice for firefighters
Fire Fighting Procedures: Keep people away. Isolate fire and deny unnecessary entry. Use water spray to cool fire exposed containers and fire affected zone until fire is out and danger of reignition has passed.Fight fire from protected location or safe distance. Consider the use of unmanned hose holders or monitor nozzles. Immediately withdraw all personnel from the area in case of rising sound from venting safety device or discoloration of the container. Do not use direct water stream. May spread fire. Move container from fire area if this is possible without hazard. Burning liquids may be moved by flushing with water to protect personnel and minimize property damage.
Special protective equipment for firefighters: Wear positive-pressure self-contained breathing apparatus (SCBA) and protective fire fighting clothing (includes fire fighting helmet,coat, trousers, boots, and gloves). If protective equipment is not available or not used, fight fire from a protected location or safe distance.
6. ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures
Isolate area. Keep unnecessary and unprotected personnel from entering the area. No smoking in area. Refer to section 7, Handling, for additional precautionary measures. Use appropriate safety equipment. For additional information, refer to Section 8, Exposure Controls and Personal Protection
Environmental precautions
Prevent from entering into soil, ditches, sewers, waterways and/or groundwater. See Section 12, Ecological Information.
Methods and materials for containment and cleaning up
Contain spilled material if possible. Small spills: Absorb with materials such as: Non-combustible material. Clay. Zorb-all®. Large spills: Dike area to contain spill. Collect in suitable and properly labeled containers. See Section 13, Disposal Considerations, for additional information.
7. HANDLING AND STORAGE
Precautions for safe handling
Do not swallow. Avoid contact with eyes, skin, and clothing. Use with adequate ventilation. Wash thoroughly after handling. Keep away from heat, sparks and flame. See Section 8, EXPOSURE CONTROLS AND PERSONAL PROTECTION.
Conditions for safe storage, including any incompatibilities
Keep from freezing - product stability may be affected. STIR WELL BEFORE USE.
Storage stability
Storage temperature: 1°C - 49°C (34°F - 120°F)
See SECTION 8, for types of ventilation required.
8. EXPOSURE CONTROL / PERSONAL PROTECTION
Control parameters
Exposure limits are listed below, if they exist.
| Components | CAS No. | Value type (Form of exposure) | Control parameter/Permissible conc. | Basis |
| Ethylene glycol monobutyl ether |
111-76-2 |
TWA |
20 ppm 240 mg/m3 50 ppm BEI Absorbed via skin |
ACGIH OSHA Z-1 ACGIH OSHA Z-1 |
| Diethylene glycol | 111-46-6 | TWA | 10 mg/m3 | US WEEL |
Exposure controls
Engineering controls: Use local exhaust ventilation, or other engineering controls to maintain airborne levels below exposure limit requirements or guidelines. If there are no applicable exposure limit requirements or guidelines, general ventilation should be sufficient for most operations. Local exhaust ventilation may be necessary for some operations.
Individual protection measures
| Eye/Face Protection | Use chemical goggles. If exposure causes eye discomfort, use a full-face respirator. |
| Skin Protection | No precautions other than clean body covering clothing should be needed. |
|
Hand Protection |
Chemical protective gloves is not needed when handling this material. Consistent with general hygienic practice for any material, skin contact should be minimized. In case of using gloves, use gloves chemically resistant to this material. Examples of preferred glove barrier materials include: Neoprene. Nitrile/ butadiene rubber ("nitrile" or "NBR"). Polyvinyl chloride ("PVC" or "vinyl"). Avoid gloves made of: Polyvinyl alcohol ("PVA"). |
|
Respiratory Protection |
Respiratory protection should be worn as there is a risk of exposure above given or recommended Occupational Exposure Limits. If such limit values are not present, respiratory protection will cause effects such as respiratory irritation or discomfort, or when risk assessment indicates that this is required. Under most conditions, no respiratory protection should be required; If discomfort is experienced, use an approved respiratory protective device. |
| Hygiene measures | Wash hands before breaks and at the end of workday.c |
9. PHYSICAL AND CHEMICAL PROPERTIES
| Appearance: | Liquid |
| Color: | Clear |
| Odor: | N/A |
| Odor Threshold: | No data available |
| pH: | 6.5-7.5 |
| Melting Point: | No data available |
| Boiling Point: | No data available |
| Flash Point: | Not applicable |
| Evaporation rate: | No data available |
| Flammability: | Not applicable |
| Upper flammability or explosive limits: | No data available |
| Lower flammability or explosive limits: | No data available |
| Vapor Pressure (mm Hg): | 18.0 |
| Vapor Density (air=1): | <1 |
| Relative Density: | 8.17 lbs./gal at 20°C |
| Specific Gravity (H2O = 1) | 1.0 - 1.2 |
| Solubility: | Completely |
| Partition coefficient: | No data available |
| Auto-ignition temperature: | No data available |
| Decomposition temperature: | No data available |
| Viscosity: | No data available |
| Explosive properties: | No data available |
| Oxidizing properties: | No data available |
Other information
| VOC per Method 24 of EPA: | 6% VOC by wt. |
10. STABILITY AND REACTIVITY
Reactivity: No dangerous reaction known under conditions of normal use.
Chemical stability: Stable product at normal conditions.
Possibility of hazardous reactions: Hazardous polymerization will not occur.
Conditions to avoid: Temperatures above 100°F (38°C) and below 34°F (1°C).
Incompatible materials: Avoid contact with: Strong acids. Strong oxidizers.
Hazardous decomposition products: Decomposition products depend upon temperature, air supply and the presence of other materials. Decomposition products can include and are not limited to: Aldehydes. Ketones. Organic acids.
SECTION 11 — TOXICOLOGICAL INFORMATION
Information on toxicological effects
Acute Toxicity
| Acute oral toxicity |
Very low toxicity if swallowed. Harmful effects not anticipated from swallowing small amounts. Based on information for component(s): LD50, Rat, > 5,000 mg/kg Estimated. |
| Acute dermal toxicity |
Prolonged skin contact is unlikely to result in absorption of harmful amounts. Based on information for component(s): LD50, Rabbit, > 5,000 mg/kg Estimated. |
| Acute inhalation toxicity |
Brief (minutes) exposure to vapor, mist or dust is not likely to cause adverse effects. The LC50 has not been determined. |
Skin corrosion/irritation
Brief contact may cause skin irritation with local redness.
Serious eye damage/eye irritation
May cause moderate corneal injury.
Sensitization
No relevant data found.
Specific Target Organ Systemic Toxicity (Single Exposure)
Evaluation of available data suggests that this material is not an STOT-SE toxicant.
Specific Target Organ Systemic Toxicity (Repeated Exposure)
Based on available data, repeated exposures are not anticipated to cause significant adverse effects.
Carcinogenicity
For the component(s) tested: Did not cause cancer in laboratory animals.
Teratogenicity
For the component(s) tested: Did not cause birth defects or any other fetal effects in laboratory animals.
Reproductive toxicity
For the component(s) tested: Did not interfere with reproduction.
Mutagenicity
In vitro genetic toxicity studies were negative for component(s) tested. Genetic toxicity studies in animals were
negative for component(s) tested.
Aspiration Hazard
Based on physical properties, not likely to be an aspiration hazard.
COMPONENTS INFLUENCING TOXICOLOGY:
| Ethylene glycol monobutyl ether | Oral Toxicity | (Guinea Pig) (Male Rat) |
LD50 = 1,400 mg/kg LD50 = 1,746 mg/kg |
| CAS No.: 111-76-2 |
Skin Toxicity |
(Rat) (Rabbit) (Guinea Pig) |
LD50 = 2,270 mg/kg LD50 = 99-610 mg/kg LD50 > 2,000 mg/kg |
| Inhalation Toxicity | (Rat) | LC50 = 700 ppm, 7 hrs, Vapor |
12. ECOLOGICAL INFORMATION
Ecotoxicological information appears in this section when such data is available.
Toxicity
Ethylene glycol monobutyl ether
Acute toxicity to fish
Material is practically non-toxic to aquatic organisms on an acute basis (LC50/EC50/EL50/LL50 >100 mg/L in the most sensitive species tested).
LC50, Oncorhynchus mykiss (rainbow trout), static test, 96 Hour, 1,474 mg/l, OECD Test Guideline 203
Acute toxicity to aquatic invertebrates
EC50, Daphnia magna (Water flea), static test, 48 Hour, 1,550 mg/l, OECD Test Guideline 202
Acute toxicity to algae/aquatic plants
EbC50, Pseudokirchneriella subcapitata (green algae), static test, 72 Hour, Biomass, 911 mg/l, OECD Test
Guideline 201
Toxicity to bacteria
IC50, Bacteria, Growth inhibition, > 1,000 mg/l
Chronic aquatic toxicity
Chronic toxicity to fish
NOEC, Danio rerio (zebra fish), semi-static test, 21 d, > 100 mg/l
Chronic toxicity to aquatic invertebrates
NOEC, Daphnia magna (Water flea), semi-static test, 21 d, Other, 100 mg/l
Persistence and degradability
Ethylene glycol monobutyl ether
Biodegradability: Material is readily biodegradable. Passes OECD test(s) for ready biodegradability. Material is ultimately biodegradable (reaches > 70% mineralization in OECD test(s) for inherent
biodegradability).
10-day Window: Pass
Biodegradation: 90.4 %
Exposure time: 28 d
Method: OECD Test Guideline 301B or Equivalent
Theoretical Oxygen Demand: 2.30 mg/mg
Chemical Oxygen Demand: 2.21 mg/g Dichromate
Biological oxygen demand (BOD)
| Incubation Time | BOD |
| 5 d | 5.2 % |
| 10 d | 57 % |
| 20 d | 72.2 % |
Bioaccumulative potential
Ethylene glycol monobutyl ether
Bioaccumulation: Bioconcentration potential is low (BCF < 100 or Log Pow < 3).
Partition coefficient: n-octanol/water(log Pow): 0.81 Measured
Bioconcentration factor (BCF): 3.2
Mobility in soil
Ethylene glycol monobutyl ether
Potential for mobility in soil is high (Koc between 50 and 150).
Partition coefficient(Koc): 67 Estimated.
13. DISPOSAL CONSIDERATIONS
Disposal methods
| Product |
Coagulate the product by the stepwise of Ferric Chloride and Lime. Remove the clear supernatant liquid and flush to a chemical sewer. Incinerate the solids and the contaminated material according to local and federal regulations. |
14. TRANSPORT INFORMATION
| DOT (Department of Transportation) | Not regulated for transport |
| Classification for SEA transport (IMO-IMDG) |
Not regulated for transport Consult IMO regulations before transporting ocean bulk. |
| Classification for AIR transport (IATA/ICAO) |
Not regulated for transport |
15. REGULATORY INFORMATION
Superfund Amendment and Reauthorization Act of 1986 Title III (Emergency Planning and Community
Right-to-Know Act of 1986)
| Section 302 and 303 | No chemicals in this product are subject to the reporting requirements of Section |
| Section 304 | No chemicals in this product are subject to the reporting requirements of Section 304 Reportable Quantity (RQ). |
| Section 311 and 312 | No SARA Hazard |
| Section 313 | This product contains the following substances which are subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and which are listed in 40 CFR 372. |
| Ingredient(s) | CAS No. | Weight % |
SARA 313 - Threshold Values % |
| Ethylene glycol monobutyl ether | 111-76-2 | 5 - 25% | 5 - 25% |
RIGHT TO KNOW (RTK)
| Ingredients | CAS # | MARTK | NJRTK | PARTK |
| Ethylene glycol monobutyl ether | 111-76-2 | - | - | X |
| Diethylene glycol | 111-46-6 | - | - | X |
California Proposition 65
This product contains a chemical that is at or below California Proposition 65's "safe harbor level" as determined via a risk assessment. Therefore, the chemical is not required to be listed as a Prop 65 chemical on SDS or label.
United States TSCA Inventory (TSCA)
All components of this product are in compliance with the inventory listing requirements of the US Toxic Substances Control Act (TSCA) Chemical Substance Inventory.
16. OTHER INFORMATION
| HMIS RATING | Health 1, Reactivity 0, Flammability 0, Personal Protection B |
| NFPA RATING | Special Hazard: N/A, Health: 1, Flammability: 0, Instability: 0 |
| SDS Updated | 2022-03-24 |
Disclaimer
OTHER INFORMATION: This information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any other process. Such information is to the best of the company’s knowledge and believed accurate and reliable as of the date indicated. However, no representation, warranty or guarantee of any kind, express or implied, is made as to its accuracy, reliability or completeness and we
assume no responsibility for any loss, damage or expense, direct or consequential, arising out of use. It is the user’s responsibility to satisfy himself as to the suitableness and completeness of such information for his own particular use.